Skip to content
Guides

Screw conveyor capacity and drive power

How to work out the capacity of a screw conveyor from its diameter, pitch, speed and fill, and the drive power with the ISO 7119 method, with a worked example for cement.

By Site AdministratorUpdated 6 min read

Screw conveyors (augers) move powders, grains and granular solids over short distances: from a silo to a mixer, from a hopper to a bagging machine, or along the bottom of a bin. They are compact, enclosed and easy to feed, but they are easy to undersize too. A screw that is a little too small or too slow will not reach the tonnage you need, and a motor picked by guesswork will trip when the trough fills up. This guide shows how to estimate capacity from the screw's geometry and the drive power from the ISO 7119 method, with a worked example you can check by hand. For a general overview of the machine, see the Wikipedia article on screw conveyors.

Diagram of a screw conveyor showing screw diameter D, pitch S, speed n, the partly filled trough with fill factor ψ in cross-section, and conveyed flow Q

A screw of diameter D and pitch S turns at n rpm inside a trough. The material lies in the lower part of the trough (fill factor ψ) and is pushed forward one pitch for every turn.

How a screw conveyor moves material

A helical flight on a shaft turns inside a U-shaped trough or a tube. The material does not rotate with the screw; friction against the trough holds it back, so each turn of the screw pushes the material forward by roughly one pitch. In an ideal case, a completely full screw would deliver one swept volume (the area of the screw circle times the pitch) per revolution. In practice the trough is only partly full, the material slips back over the flight, and inclining the conveyor makes slip worse. Those effects are handled with two correction factors: the fill (loading) factor ψ and the inclination factor C.

The capacity formula

The mass capacity of a screw conveyor with a full-pitch continuous flight is:

Q = 60 × (π × D² ÷ 4) × S × n × ψ × ρ × C

  • Q is the capacity, in tonnes per hour (t/h).
  • D is the screw diameter and S is the pitch, both in metres. Standard screws have S equal to D; short-pitch screws (S ≈ 0.5 to 0.75 D) are used for inclines and feeders.
  • n is the screw speed, in rpm. The factor 60 turns minutes into hours.
  • ψ is the fill factor, the fraction of the trough cross-section the material occupies.
  • ρ is the bulk density, in t/m³ (not the solid density of the particles).
  • C is the inclination factor.

Bulk density is the number people most often get wrong. Cement, for example, is about 1.2 t/m³ aerated in a conveyor but can exceed 1.5 t/m³ when packed. If you have figures in lb/ft³ or kg/L, the engineering unit converter will put them into t/m³.

Typical fill factors

  • Light, free-flowing, non-abrasive materials (grain, flour, plastic pellets): ψ = 0.40 to 0.45.
  • Mildly abrasive materials (cement, salt, coal fines, lime): ψ = 0.25 to 0.30.
  • Abrasive, heavy materials (sand, ash, clinker, ores): ψ = 0.125 to 0.15.

Published tables differ slightly; if the conveyor maker gives a value for your material, use theirs.

Inclination factor C

Commonly used values are C = 1.0 for a horizontal screw, 0.9 at 5°, 0.8 at 10°, 0.7 at 15° and 0.65 at 20°. Above about 20° the capacity falls quickly, and steeply inclined or vertical screws need a different design method.

Drive power by the ISO 7119 method

ISO 7119 (Continuous mechanical handling equipment for loose bulk materials: screw conveyors, design rules for drive power) splits the power at the screw shaft into three parts:

P = PH + PN + Pst

  • PH = Q × L × λ ÷ 367 is the power to move the material along the conveyor, in kW. L is the conveyor length in metres and λ is the progress resistance coefficient of the material.
  • PN = D × L ÷ 20 is the no-load power (bearings, seals, turning the empty screw), in kW, with D and L in metres.
  • Pst = Q × H ÷ 367 is the power to lift the material through height H in metres (positive going up, negative going down).

The constant 367 comes from g = 9.81 m/s² and the conversion of t/h to kg/s: 3,600 ÷ 9.81 ≈ 367. The coefficient λ is generally between about 2 and 4; free-flowing, non-abrasive materials sit near the bottom of that range and sticky or abrasive materials such as cement, ash and sand near the top. The standard's annex and conveyor makers' catalogues list values for specific materials.

Worked example: a cement screw

A plant needs to move 20 t/h of cement from a silo to a mixer. The conveyor is 12 m long and inclined at 10°. Try a standard-pitch screw of D = 0.30 m and S = 0.30 m.

Step 1: capacity per rpm

  • Swept area: π × 0.30² ÷ 4 = 0.0707 m².
  • Swept volume per turn: 0.0707 × 0.30 = 0.0212 m³.
  • Fill factor for cement: ψ = 0.30. Bulk density: ρ = 1.2 t/m³. At 10°: C = 0.8.
  • Q per rpm = 60 × 0.0212 × 0.30 × 1.2 × 0.8 = 0.366 t/h.

Step 2: speed

The minimum speed for 20 t/h is 20 ÷ 0.366 = 54.6 rpm. With a 4-pole motor at about 1,450 rpm and a 25:1 gearbox, the screw turns at 1,450 ÷ 25 = 58 rpm, giving Q = 0.366 × 58 = 21.3 t/h, about 17.7 m³/h. That is enough, with a small margin. Check the speed against the maker's maximum for a 300 mm screw handling a mildly abrasive material.

Step 3: drive power

  • Lift: H = 12 × sin 10° = 2.08 m.
  • Progress resistance: take λ = 4.0, the conservative end of the range, for cement.
  • PH = 21.3 × 12 × 4.0 ÷ 367 = 2.79 kW.
  • PN = 0.30 × 12 ÷ 20 = 0.18 kW.
  • Pst = 21.3 × 2.08 ÷ 367 = 0.12 kW.
  • P = 2.79 + 0.18 + 0.12 = 3.09 kW at the screw shaft.

Bar chart of the screw conveyor power: P_H 2.79 kW, P_N 0.18 kW, P_st 0.12 kW, total 3.09 kW at the shaft and 3.63 kW at the motor, rounded up to a 4 kW motor

Moving the material along the trough takes most of the power; lifting it 2 m adds very little.

Step 4: motor and torque

With a combined gearbox and coupling efficiency of about 0.85, the motor must deliver 3.09 ÷ 0.85 = 3.63 kW. The next standard size is 4 kW, about 10% above the requirement. If the conveyor may have to start full of packed cement, many designers go one size up to 5.5 kW. The torque at the screw shaft is T = 9,550 × P ÷ n = 9,550 × 3.09 ÷ 58 ≈ 509 N·m, which the gearbox output shaft, coupling and screw shaft must carry. The motor and gearbox selection calculator does the kW-to-torque and ratio steps for you.

Screw or belt?

Screws suit dusty or hot materials, short runs and metered feeding, because they are enclosed and their output follows speed closely. Their power per tonne is much higher than a belt's, because the material is dragged along a trough rather than carried. For long horizontal runs of tens of tonnes an hour, compare the numbers with a belt: the belt conveyor capacity and drive power guide and the belt conveyor calculator show the same job done on a belt.

Practical points for screw conveyor sizing

  • Use the bulk density as conveyed, not the packed or particle density, and check the heaviest condition for power.
  • Keep the fill factor within the range for the material. Overfilling an abrasive material wears the flights and trough quickly and raises the power sharply.
  • Do not let the screw run choke-full unless it is designed as a feeder with a short-pitch or tapered flight.
  • Inlet sections under a silo can flood. Fit a short-pitch section or a feeder so that the main screw sees a controlled flow.
  • Allow for start-up under load: the motor, gearbox and shaft must carry the torque of a full trough.
  • Treat these formulas as a sizing estimate. Confirm the final diameter, speed and motor with the conveyor maker's data for your material.
#ISO 7119#conveyor capacity#screw conveyor#drive power#auger#bulk materials

Keep reading