Gear ratio calculation: speed, torque and centre distance
How to calculate gear ratio, output speed and torque for a gear pair and a multi-stage gear train, with module, centre distance, tooth force and a worked two-stage 4 kW reducer example.
A motor turns at 1,450 rpm, but the conveyor, mixer or winch it drives needs 60 rpm and a lot more torque. Gears close that gap. The gear ratio calculation tells you how many teeth each gear needs, how fast every shaft turns, how much torque reaches the output, and how far apart the shafts must sit. This guide covers the formulas for a single gear pair, then for multi-stage gear trains, explains module, centre distance, tooth force and how to choose tooth counts, and finishes with a fully worked two-stage reducer for a 4 kW conveyor drive.
What the gear ratio means
When two spur gears mesh, the same number of teeth pass the contact point every second on both gears. A gear with more teeth therefore turns more slowly. The gear ratio is:
i = z2 / z1 = n1 / n2 = d2 / d1
- z1, z2 = number of teeth on the driving gear (pinion) and the driven gear
- n1, n2 = speeds of the two shafts, rpm
- d1, d2 = pitch diameters, mm
A ratio above 1 is a reduction: the output turns slower and with more torque. A ratio below 1 is a step-up (overdrive). Ratios are usually written as "3.06 : 1", meaning the input turns 3.06 times for one turn of the output.
Speed, torque and power through a gear pair
A gear pair passes power on almost unchanged, and power is torque times speed. So whatever the gears take away in speed, they give back in torque, less a small loss in the mesh:
n2 = n1 / i
T2 = T1 × i × η
P = T × n / 9550 (P in kW, T in N·m, n in rpm)
η is the mesh efficiency. Well-made, well-lubricated spur gears at a reasonable load are commonly taken as about 98% per mesh (0.97 to 0.99 is the usual planning range). Efficiency falls at very light loads, where churning and bearing losses dominate, and with rough or worn teeth.
Example: an 18-tooth pinion on a 1,450 rpm shaft delivering 10 N·m drives a 55-tooth gear. i = 55 / 18 = 3.056, the output turns at 1,450 / 3.056 = 474.5 rpm, and the output torque is 10 × 3.056 × 0.98 = 29.9 N·m (30.6 N·m with no losses).
Gear trains: when one pair is not enough
Simple trains and idler gears
In a simple train each shaft carries one gear. An idler gear placed between the driver and the driven gear changes nothing about the ratio: its teeth cancel out (z2/z1 × z3/z2 = z3/z1). It does two other things: it reverses the direction of rotation once more, and it lets you bridge a larger centre distance without making either end gear bigger. Each extra mesh still costs about 2% efficiency.
Compound trains
In a compound train an intermediate shaft carries two gears: a large gear driven by the first pinion and a small pinion driving the next stage. The ratios multiply:
i_total = (z2 / z1) × (z4 / z3) × … = product of driven teeth / product of driving teeth
η_total = η1 × η2 × … (two stages at 0.98 give 0.960; three give 0.941)
Each pair turns in the opposite direction to the one before it, so a two-stage compound reducer has its output turning the same way as the motor, and a single or three-stage one turns it the other way.
Splitting a large ratio into stages
A single spur pair is usually kept to about 5:1 or 6:1. The reason is simple arithmetic: a 24:1 reduction in one step with a 17-tooth pinion would need a 410-tooth wheel, more than a metre across at module 2.5. Two stages of about 5:1 and 4.6:1 give the same ratio with gears a quarter of that size. A common rule is to give the first (high-speed) stage a slightly larger ratio than the second, because the torque there is lower and the gears are smaller.
Module, pitch diameter and centre distance
The module m is the metric measure of tooth size, in millimetres. Two gears can only mesh if they have the same module and pressure angle (20° is standard). From the module:
d = m × z (pitch diameter, mm)
da = m × (z + 2) (outside diameter of a standard gear without profile shift, mm)
a = m × (z1 + z2) / 2 (centre distance between the two shafts, mm)
Use a standard module so cutters and stock gears are available. The preferred (series I) values in ISO 54 include 1, 1.25, 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm. Inch gears use diametral pitch instead: P = z / d (teeth per inch of pitch diameter), and m = 25.4 / P. A 10 DP gear is module 2.54, close to but not interchangeable with module 2.5.
Pitch-line speed and tooth force
Two more numbers tell you whether the gear pair is reasonable before any detailed strength check:
v = π × d × n / 60,000 (pitch-line speed, m/s, with d in mm)
Ft = 2000 × T / d (tangential tooth force, N, with T in N·m and d in mm)
The pitch-line speed affects noise, dynamic load and the kind of lubrication needed; spur gears get noisy as v rises, which is why fast stages often use helical gears. The tangential force is what the teeth, and later the shafts and bearings, must carry. It is the same on both gears of a pair, which is why the slow, high-torque end of a reducer needs larger gears, not stronger formulas.
Choosing tooth counts
- Minimum teeth on the pinion. A standard 20° spur pinion cut by a rack-type cutter starts to undercut below 17 teeth, which weakens the tooth root. Fewer teeth (down to about 12 to 14) are possible with a profile shift and a strength check, but 17 or more keeps things simple.
- Hunting tooth. Choose tooth counts with no common factor (for example 18 and 95, not 18 and 90). Then every tooth on the pinion meets every tooth on the gear in turn, and wear and small errors are spread evenly instead of repeating on the same few teeth.
- Ratio tolerance. Whole tooth numbers rarely give the exact ratio you want. A driven machine usually tolerates a few per cent; if the speed matters exactly, search combinations of tooth counts (or let the calculator do it) until the error is small enough.
- Size and space. Check the centre distance and the outside diameters against the housing and the shaft sizes. A pinion has to be big enough for its bore and key: our guide to shaft diameter from torque and bending shows how to size the shaft it sits on.
Worked example: gear ratio calculation for a two-stage conveyor reducer
A belt conveyor head pulley must turn at 60 rpm. It is driven by a 4 kW, 4-pole motor running at 1,450 rpm through a two-stage spur gear reducer. Take η = 0.98 per mesh and modules of 2.5 mm for the fast stage and 4 mm for the slow stage.
1. Total ratio needed: i = 1,450 / 60 = 24.17.
2. Split into two stages: √24.17 ≈ 4.92, so aim for about 5.2 and 4.6. Searching tooth counts with no common factor gives z1 = 18, z2 = 95 (i1 = 5.278) and z3 = 19, z4 = 87 (i2 = 4.579). Total i = 5.278 × 4.579 = 24.17, so the output speed is 1,450 / 24.17 = 60.0 rpm, exactly on target.
3. Motor torque: T1 = 9550 × 4 / 1,450 = 26.3 N·m.
4. Intermediate shaft: n = 1,450 / 5.278 = 274.7 rpm; T = 26.3 × 5.278 × 0.98 = 136.3 N·m.
5. Output shaft: n = 60 rpm; T = 136.3 × 4.579 × 0.98 = 611.5 N·m (636.7 N·m without losses). Output power is 611.5 × 60 / 9550 = 3.84 kW; the overall efficiency is 0.98² = 0.960.
6. Geometry, stage 1 (m = 2.5): d1 = 45 mm, d2 = 237.5 mm, a1 = 2.5 × (18 + 95) / 2 = 141.25 mm.
7. Geometry, stage 2 (m = 4): d3 = 76 mm, d4 = 348 mm, a2 = 4 × (19 + 87) / 2 = 212 mm.
8. Pitch-line speed and tooth force: stage 1: v = π × 45 × 1,450 / 60,000 = 3.42 m/s, Ft = 2000 × 26.3 / 45 = 1,171 N. Stage 2: v = π × 76 × 274.7 / 60,000 = 1.09 m/s, Ft = 2000 × 136.3 / 76 = 3,586 N.
Shaft | Speed (rpm) | Torque (N·m) | Gears on shaft |
|---|---|---|---|
A (motor) | 1,450 | 26.3 | z1 = 18, d 45 mm |
B (intermediate) | 274.7 | 136.3 | z2 = 95, d 237.5 mm; z3 = 19, d 76 mm |
C (output) | 60.0 | 611.5 | z4 = 87, d 348 mm |
The output shaft carries more than 23 times the motor torque, so it, its key and its bearings need to be sized for 611.5 N·m plus any service factor for shock loading, not for the 4 kW nameplate figure. The same drive in imperial terms: 4 kW = 5.36 hp, and 611.5 N·m = 451 lbf·ft at the output.
Common mistakes in gear ratio calculations
- Turning the ratio upside down. Driven teeth go on top. 18/55 instead of 55/18 gives a speed-up of 3 instead of a reduction of 3.
- Counting the idler. An idler changes direction and centre distance, not the ratio. Leave it out of the product, but keep its mesh loss.
- Forgetting the losses. Two or three stages at 98% each remove 4 to 6% of the torque. On a lifting drive with no margin, that matters.
- Mixing module and diametral pitch. Module 2.5 and 10 DP look almost the same but will not run together. Check the units on every catalogue page; our unit converter helps with inches, hp and lbf·ft.
- Using the nameplate torque for the output shaft. Torque multiplies through the train. Size each shaft for the torque on that shaft.
- Too few pinion teeth. Below 17 teeth at 20° without profile shift, the tooth roots are undercut and weaker.
Quick reference
- Ratio: i = z2 / z1 = n1 / n2; train: i = product of driven teeth / product of driving teeth
- Output speed: n2 = n1 / i
- Output torque: T2 = T1 × i × η (η ≈ 0.98 per spur mesh)
- Power: P = T × n / 9550 (kW, N·m, rpm)
- Pitch diameter: d = m × z; outside diameter da = m × (z + 2)
- Centre distance: a = m × (z1 + z2) / 2
- Pitch-line speed: v = π × d × n / 60,000 (m/s)
- Tangential force: Ft = 2000 × T / d (N)
- Diametral pitch: m = 25.4 / P
To try your own tooth counts, use the gear ratio calculator, which returns the ratio, output speed and torque, pitch diameters, centre distance and pitch-line speed for a spur gear pair. To choose the motor and the overall reduction first, see the motor and gearbox calculator and our guide to choosing a motor and gearbox from power and speed. These figures give speeds, torques and sizes; whether the teeth are strong enough depends on face width, material, heat treatment and lubrication, and needs a strength check to a standard such as ISO 6336 or AGMA 2001. For background, see Gear train (Wikipedia).