Skip to content
Guides

Choosing a motor and gearbox from power and speed

How the Motor & gearbox selection calculator turns absorbed power, motor speed, output speed and service factor into gearbox ratio, shaft torque, design power and a standard motor frame.

By Site AdministratorUpdated 3 min read

A drive is chosen on three things: the power the machine absorbs, the speeds at each end, and how hard the machine works. The Motor & gearbox selection calculator takes absorbed power, motor speed, output speed and a service factor, and gives the gearbox ratio, the torque on each shaft, the design power to select a gearbox on and a standard motor frame.

How the calculation works

You enter absorbed power (kW), motor speed (rpm), output speed (rpm) and a service factor. The tool then works out:

  • Horsepower = kW × 1.34102.
  • Gearbox ratio = motor rpm ÷ output rpm.
  • Motor shaft torque (N·m) = 9550 × kW ÷ motor rpm.
  • Output shaft torque (N·m) = 9550 × kW ÷ output rpm.
  • Design power (kW) = kW × service factor. This is the figure to select the gearbox on.
  • Output torque with service factor = output torque × service factor. This is the figure to check a gearbox rating against.
  • Motor frame = kW × 1.15, rounded up to the next standard IEC size in the tool's list, which runs from 0.37 kW to 400 kW.

The tool's guide for the service factor is 1.0 for uniform load, 1.25 for moderate shock, 1.5 for heavy duty and 1.75 or more for crushers and mills. For motor speed it suggests 1450 rpm for a 4-pole motor at 50 Hz, 2900 for 2-pole and 960 for 6-pole.

A worked example

An agitator absorbs 15 kW. The motor is a 4-pole at 1450 rpm, the agitator should turn at 45 rpm and the service is heavy, so the service factor is 1.5. These are the tool's starting values:

  • Horsepower = 15 × 1.34102 = 20.12 HP.
  • Gearbox ratio = 1450 ÷ 45 = 32.22 : 1.
  • Motor shaft torque = 9550 × 15 ÷ 1450 = 98.8 N·m.
  • Output shaft torque = 9550 × 15 ÷ 45 = 3,183 N·m.
  • Design power = 15 × 1.5 = 22.5 kW, and output torque with service factor = 3,183 × 1.5 = 4,775 N·m.
  • Motor frame: 15 × 1.15 = 17.25 kW, so the next standard size is 18.5 kW (24.8 HP).

So the gearbox is selected on 22.5 kW or 4,775 N·m at roughly 32 : 1, and the motor is an 18.5 kW frame. Notice how the torque rises by a factor of 32 on the slow shaft: the output end is the expensive part of the drive, not the motor. If the agitator had to turn at 30 rpm instead, the ratio would be 48.33 : 1 and the output torque 4,775 N·m, or 7,163 N·m with the service factor, while the motor frame stays at 18.5 kW. Slowing the machine down does not change the motor, but it makes the gearbox bigger.

What the tool assumes and leaves out

  • The power you enter is what the driven machine absorbs at its shaft. The tool does not add gearbox losses.
  • The ratio is a plain division. Real gearboxes come in fixed catalogue ratios, so choose the nearest one and recalculate the output speed.
  • The motor frame is based on absorbed power with 15% margin, while the gearbox is selected on design power with the service factor. The two are separate figures.
  • Torque is calculated from power and speed alone. Starting torque, inertia, thermal rating, overhung loads and variable-speed drives are not covered.
  • The speed hints assume 50 Hz. On other supplies, enter the actual motor speed.

Common mistakes

  • Entering the motor nameplate power as the absorbed power. That already includes a margin, so the service factor then adds a second one.
  • Applying the service factor to the motor as well as to the gearbox.
  • Checking the coupling and shaft against the motor torque instead of the much larger output torque.
  • Entering a speed that is not the true full-load speed of the motor or of the driven machine.
  • Treating the calculated ratio as an exact catalogue ratio.
  • Leaving the service factor at 1.0 for a machine that starts under load or takes shocks.

Run your own drive in the Motor & gearbox selection calculator. To find the absorbed power of a pump first, use the pump head and power calculator, and for a belt use the belt conveyor calculator.

Keep reading