Skip to content
Guides

Chain drive sizing: sprockets, chain length and centre distance

How to size a roller chain drive: speed ratio and sprocket teeth, pitch diameter, chain speed and pull, the chordal effect, chain length in links and the true centre distance, worked through for a 5.5 kW conveyor drive at 50 rpm.

By Site AdministratorUpdated 9 min read

A roller chain drive is one of the simplest ways to move power between two parallel shafts: no slip, a fixed speed ratio, high torque at low speed and a tolerance for dust and heat that a belt would not survive. It is also easy to get wrong. A sprocket with too few teeth makes the chain jerk and wear quickly, a centre distance picked from the drawing leaves half a link of slack nobody can take up, and a chain chosen on breaking strength alone can fail by fatigue long before it reaches that load. A sound chain drive calculation needs only a few formulas: the speed ratio, the sprocket pitch diameters, the chain speed and pull, the chain length in links and the true centre distance. This guide works through each one, with a complete example for a 5.5 kW gearmotor driving a conveyor head shaft.

Diagram of a roller chain drive with a 19-tooth driving sprocket (154.3 mm pitch diameter, 150 rpm) and a 57-tooth driven sprocket (461.1 mm, 50 rpm) about 1,030 mm apart, ANSI 80 chain of 120 links, chain pull F = P / v of about 4.56 kN and the pitch diameter and chain speed formulas

Step 1: speed ratio and sprocket teeth

A chain moves the same number of links past each sprocket, so the speed ratio is set by the tooth counts alone:

i = N2 / N1 = n1 / n2

  • N1, N2 = teeth on the driving (small) and driven (large) sprocket
  • n1, n2 = speed of the driving and driven shaft, rpm

The ratio is exact and does not change with load, which is the main reason to choose a chain over a belt for a timing-sensitive or heavily loaded drive. Some practical limits come from chain makers' design guidance:

  • Small sprocket: 17 teeth or more for general industrial drives, 19 to 21 or more for higher speeds or shock loads. Below about 15 teeth the chain runs rough (see Step 3).
  • Odd tooth counts on at least one sprocket, combined with an even number of links, spread wear more evenly because the same link does not meet the same tooth every revolution.
  • Ratio per stage: up to about 7:1 is common for one chain stage. Beyond that, a two-stage drive or a gearbox is usually better.

Step 2: pitch diameter of each sprocket

The chain pitch p is the distance between roller centres: 12.7 mm (1/2 in) for ANSI 40, 15.875 mm for ANSI 50, 19.05 mm for ANSI 60 and 25.4 mm (1 in) for ANSI 80, for example. The rollers sit on the pitch circle, which is a polygon of N sides of length p, so:

D = p / sin(180° / N)

The pitch diameter is what you use for torque and chain pull. It is a little larger than N × p / π, the value you would get by treating the sprocket as a smooth pulley, and the difference matters for small sprockets. ANSI and ISO 606 "A series" chains of the same pitch are dimensionally the same (ANSI 80 is ISO 16A), but the British "B series" chains such as 16B have the same pitch with different roller and width dimensions, so do not mix them on one drive.

Step 3: chain speed, chain pull and the chordal effect

Average chain speed is the number of links passing per second times the pitch:

v = p × N1 × n1 / 60,000 (m/s, with p in mm and n1 in rpm)

The working pull in the tight strand follows from the power:

F = P / v (N, with P in W and v in m/s)

In imperial units the same relation is F (lbf) = 33,000 × hp / v (ft/min). The slack strand carries almost no load in a well-set drive, so F is also, to a good approximation, the side load on each shaft. That is the load to use for bearing life and for the bending check in our shaft diameter guide.

Because the chain wraps a polygon rather than a circle, its speed rises and falls slightly as each link engages. This is the chordal effect, and the speed variation is about:

Δv / v ≈ 1 − cos(180° / N)

Bar chart of chordal speed variation 1 - cos(180°/N) for sprockets with 11, 15, 19 and 25 teeth: 4.05%, 2.19%, 1.36% and 0.79%

An 11-tooth sprocket gives about 4% speed variation, a 19-tooth sprocket about 1.4% and a 25-tooth sprocket under 0.8%. The pulsation shows up as noise, vibration and faster wear of pins and bushes, which is why the small sprocket should have as many teeth as the space allows.

Step 4: chain length in links

For two sprockets at centre distance C, the chain length in pitches (links) is:

L = 2C/p + (N1 + N2)/2 + (N2 − N1)² / (4π² × C/p)

Use C in the same unit as p, so C/p is the centre distance in pitches. A common mistake is to put C in millimetres and p nowhere, which gives a length dozens of times too long. Round L up to a whole, preferably even, number of links; an odd number needs an offset (cranked) link, which is weaker. For most drives, a centre distance of 30 to 50 pitches is a good starting point, and the wrap on the small sprocket should be at least about 120°.

Step 5: the true centre distance

Once L is rounded, the centre distance is no longer the value you started with. Solve the length formula back for C:

C = p/4 × [ A + √(A² − 8 × ((N2 − N1) / 2π)²) ], where A = L − (N1 + N2)/2

Design the motor base or take-up so the shafts can be set at this value, plus adjustment for chain stretch over its life. For a horizontal drive, a slack-side sag of roughly 2 to 3% of the centre distance is typical; check the figure your chain maker recommends. If the centre distance is fixed, use an idler or tensioner on the slack side instead.

Step 6: is the chain strong enough?

Real chain selection is done with the maker's power rating chart for each chain size, after multiplying the motor power by a service factor: about 1.0 for smooth loads driven by an electric motor, around 1.3 for moderate shock (an unevenly fed conveyor, for instance) and 1.5 or more for heavy shock. The rating charts already include fatigue of the link plates, wear of pins and bushes, and the lubrication method for each speed range. Multi-strand chains carry more, but not in direct proportion; commonly used multi-strand factors are 1.7 for duplex and 2.5 for triplex chain.

For slow drives, a quick tension check is also useful. Compare the design pull (F × service factor) with the chain's minimum tensile strength, and expect a safety factor in the region of 7 to 10. Catalogues differ, so treat this as a sanity check, not a substitute for the rating chart. Never treat the breaking strength as a working load: a roller chain should not see anything near it, even once.

Worked example: 5.5 kW gearmotor driving a conveyor at 50 rpm

A conveyor head shaft must turn at 50 rpm. The gearmotor gives 5.5 kW at 150 rpm. The load is a conveyor with uneven feed, so take a service factor of 1.3. Trial chain: ANSI 80 single strand, pitch 25.4 mm, minimum tensile strength 12,500 lbf (55.6 kN).

1. Ratio and teeth

i = 150 / 50 = 3. Choose N1 = 19 teeth and N2 = 3 × 19 = 57 teeth. Both are odd, and 19 teeth keeps the chordal speed variation to about 1.4%.

2. Pitch diameters

D1 = 25.4 / sin(180° / 19) = 25.4 / 0.1646 = 154.3 mm
D2 = 25.4 / sin(180° / 57) = 25.4 / 0.0551 = 461.1 mm

3. Chain speed and pull

v = 25.4 × 19 × 150 / 60,000 = 1.21 m/s (72 m/min)
F = 5,500 / 1.2065 = 4,559 N (about 4.6 kN)

Torque check: the gearmotor torque is 9,550 × 5.5 / 150 = 350 N·m and the head shaft torque is 9,550 × 5.5 / 50 = 1,050.5 N·m. F × D2 / 2 = 4,559 × 0.2305 = 1,051 N·m, so the numbers agree (the small difference comes from the polygon geometry). The motor and gearbox selection calculator gives the same torques and the gearbox ratio for the motor side.

4. Chain length

Start at 40 pitches (1,016 mm):

L = 2 × 40 + (19 + 57)/2 + (57 − 19)² / (4π² × 40) = 80 + 38 + 1,444 / 1,579.1 = 118.9 links

Round up to 120 links (even, no offset link). Chain length = 120 × 25.4 = 3.048 m.

5. True centre distance

A = 120 − 38 = 82; ((57 − 19)/2π)² = 6.048² = 36.58

C = 25.4/4 × [82 + √(82² − 8 × 36.58)] = 6.35 × [82 + √6,431.4] = 6.35 × 162.20 = 1,029.9 mm (40.5 pitches)

Wrap on the small sprocket = 180° − 2 × asin((461.1 − 154.3) / (2 × 1,029.9)) = 180° − 17.1° = 162.9°, well above 120°.

6. Strength check

Design power for the rating chart = 5.5 × 1.3 = 7.15 kW at 150 rpm on a 19-tooth sprocket; look this up in the maker's ANSI 80 chart. As a tension check, design pull = 4,559 × 1.3 = 5,926 N, and 55,600 / 5,926 = 9.4, inside the 7 to 10 range for a slow drive.

Imperial check

5.5 kW = 7.38 hp; chain speed = 1 in × 19 × 150 / 12 = 237.5 ft/min; F = 33,000 × 7.38 / 237.5 = 1,025 lbf, which is the same 4,559 N.

Result

ANSI 80-1 chain, 19T / 57T sprockets, 120 links, centre distance 1,030 mm plus take-up for stretch. If the rating chart shows that 7.15 kW is beyond a single-strand ANSI 80 at 150 rpm, the options are a duplex chain (about 1.7 times the rating) or a larger small sprocket, which raises the chain speed and lowers the pull. When you check the conveyor itself, the belt conveyor capacity and power calculator gives the head shaft power this chain must carry.

Chain or V-belt?

Chains suit low speeds, high torque, fixed ratios, hot or dirty places and drives where slip is not acceptable. Belts are quieter, need no lubrication and handle higher speeds and some misalignment better. For a motor at 1,450 rpm feeding a fan or pump, a belt is often the better choice; our V-belt drive guide uses the same length and centre-distance logic.

Common mistakes in chain drive sizing

  • Too few teeth on the small sprocket. Fewer than 15 teeth raises the chordal effect, noise and wear sharply.
  • Centre distance in the wrong unit. The length formula needs C in pitches.
  • No allowance for stretch. Chains elongate as pins and bushes wear; many makers recommend replacement at around 3% elongation, and sooner on drives with very large sprockets.
  • Selecting on breaking strength alone. Use the power rating chart with a service factor; the tension check is only a cross-check.
  • Ignoring lubrication. The rating charts assume the lubrication method stated for each speed band. A dry chain wears out many times faster.
  • Mixed units on the power side. Convert hp, kgf·m or lb·ft with the engineering unit converter before you start.

Quick reference: chain drive calculation formulas

  • Ratio: i = N2 / N1 = n1 / n2
  • Pitch diameter: D = p / sin(180° / N)
  • Chain speed: v = p × N1 × n1 / 60,000 (m/s, p in mm)
  • Chain pull: F = P / v
  • Chordal speed variation: 1 − cos(180° / N)
  • Length in links: L = 2C/p + (N1 + N2)/2 + (N2 − N1)² / (4π² C/p)
  • Centre distance: C = p/4 × [A + √(A² − 8((N2 − N1)/2π)²)], A = L − (N1 + N2)/2

For background on chain construction and types, see the Wikipedia article on roller chain. Pick the teeth first, get the chain speed and pull right, round the links to an even number and design in room for stretch, and a chain drive will run for years.

#centre distance#roller chain#power transmission#chain drive#chain length#sprocket

Keep reading