Skip to content
Guides

Tractors, implements and pumps for a farm from acreage

How the Agriculture machinery tool turns acreage, working window, field capacity and irrigation depth into tractor, implement and pump set counts.

By Site AdministratorUpdated 3 min read

Buy too few tractors and land preparation runs past the sowing date; buy too many and capital sits idle for most of the year. The Agriculture machinery tool takes the area, the working window, the hours per day, the field capacity and the irrigation depth, and lists the tractors, implements and pump sets that follow. You then enter your own rate against each line.

How the calculation works

You enter land under cultivation (acres), working window (days), working hours (hours/day), field capacity (acres/hour) and irrigation depth (mm/day). The tractor count is sized on the heaviest operation, normally land preparation:

  • Available hours = window days × hours per day.
  • One tractor covers = field capacity × available hours, in acres.
  • Tractors = area ÷ that figure, rounded up, never less than 1.

The other lines follow from the tractor count or the area:

  • One trailer, one plough, one disc harrow and one rotavator per tractor.
  • Seed drills = tractors ÷ 2, rounded up, because sowing follows preparation.
  • Sprayers = area ÷ 250, rounded up. Levellers = area ÷ 500, rounded up. Both at least 1.
  • Daily water (m³) = area × 4046.86 × depth in mm ÷ 1000, since an acre is 4,046.86 m² and a millimetre over one square metre is a litre.
  • Pump flow (m³/h) = daily water ÷ working hours. Pump sets = flow ÷ 100, rounded up.
  • PVC delivery pipe = 3 m per acre, and one sprinkler or drip set per acre.

The starting values are 200 acres, 25 days, 8 hours, 1.2 acres/hour and 6 mm/day.

A worked example

Take 500 acres with the other starting values.

  • Available hours = 25 × 8 = 200 h, and one tractor covers 1.2 × 200 = 240 acres.
  • Tractors = 500 ÷ 240 = 2.08, rounded up to 3. So 3 trailers, 3 ploughs, 3 harrows and 3 rotavators.
  • Seed drills = 3 ÷ 2 = 1.5, rounded up to 2. Sprayers = 500 ÷ 250 = 2. Levellers = 500 ÷ 500 = 1.
  • Daily water = 500 × 4046.86 × 6 ÷ 1000 = 12,141 m³/day, so pump flow = 12,141 ÷ 8 = 1,518 m³/h and pump sets = 16.
  • Delivery pipe = 1,500 m and sprinkler sets = 500.

At the default 200 acres the answer is a single tractor, because 200 is below the 240 acres one tractor covers. Shorten the window to 15 days and one tractor covers 144 acres, so two are needed.

Reading the result

The tractor count is driven only by the window and field capacity. The irrigation depth changes the pump and nothing else. The basis column on each line shows the arithmetic, for example 500 acres ÷ (1.20 acre/h × 200 h). Rounding up matters: 2.08 becomes 3, so a small change in acreage near a threshold adds a whole tractor and its implements. The tool lists quantities and specifications; the rate column is blank until you fill it in.

What the tool assumes and leaves out

  • It prices nothing. You supply the rate for each line and no market prices are built in.
  • Specifications are fixed: a 55 to 75 hp tractor, a 3 furrow plough, a 20 disc harrow, a 7 ft rotavator, an 11 tyne drill, a 400 litre sprayer, an 8 ft laser leveller and a 5 tonne trailer.
  • The default field capacity suits a 55 to 75 hp machine on medium soil. Heavy soil or a smaller tractor needs a lower figure.
  • Harvesters, threshers, land development, tube-well boring, storage, civil work and anything crop-specific are not included.
  • Each pump set is counted at 100 m³/h, so a large area gives many sets. Treat that as a prompt to think about fewer, larger pumps or a staggered schedule.

Common mistakes

  • Entering the whole season as the working window instead of the days available for land preparation.
  • Using a field capacity from a bigger tractor or a lighter operation.
  • Entering irrigation depth for the average day, not the peak crop water use.
  • Forgetting that working hours also set the pump flow: fewer hours means a larger pump.
  • Reading the list as a complete farm budget, when harvest equipment and civil work are left out.

Try your own figures in the Agriculture machinery calculator. To check the pipe for a pump set, use the pipe size and pressure drop calculator, and for the pump motor the pump head and power calculator.

Keep reading