Skip to content
Guides

Sugar mill machinery from daily cane tonnage

How the Sugar mill tool turns tonnes of cane a day, pol and imbibition into a mill tandem, clarifier, evaporators, vacuum pans, crystallisers and centrifugals.

By Site AdministratorUpdated 4 min read

A cane sugar mill is always described by its TCD, the tonnes of cane crushed in a day. Behind that one number sit carriers, mills, a clarifier, a multiple-effect evaporator, pans and centrifugals, and almost every one is sized from the cane rate. The Sugar mill tool takes four figures and lists each machine with a size, a quantity and the reason for it. You then enter your own rate against each line.

How the calculation works

The starting values are 2,500 tonnes of cane a day, 22 operating hours, 11% pol in cane and 28% imbibition water on cane. The tool first works out:

  • Cane rate (kg/h) = TCD × 1000 ÷ hours.
  • Mixed juice = cane rate × (1 + imbibition ÷ 100) × 0.9.
  • Sugar = cane rate × pol ÷ 100 × 0.85, that is 85% recovery.
  • Bagasse = 30% of the cane rate.
  • Evaporation load = mixed juice × 0.75, the water to boil off between juice at about 85% water and syrup at about 35%.

The lines then follow these rules:

  • Carrier, fibrizor and five three-roller mills are listed at the cane rate in tonnes an hour.
  • Four juice heaters, each 2% of the mixed juice rate in m². One clarifier with 2.5 hours of retention at a juice density of 1,050 kg/m³, rounded up to a stock size.
  • Two rotary vacuum filters of 0.4% of the cane rate in m², with a floor of 10 m².
  • Five evaporator bodies, each 0.09 m² per kg/h of evaporation load, with a floor of 200 m².
  • Four vacuum pans at 2% of the sugar rate in m³ (floor 15) and six crystallisers at 3% (floor 20), both rounded up to a stock size.
  • Six centrifugals and one dryer, grader and bagging line, listed at the sugar rate.

A worked example

Take the starting values.

  • Cane rate = 2,500,000 ÷ 22 = 113,636 kg/h, shown as 114 t/h.
  • Mixed juice = 113,636 × 1.28 × 0.9 = 130,909 kg/h. Imbibition water = 113,636 × 0.28 = 31,818 kg/h.
  • Sugar = 113,636 × 0.11 × 0.85 = 10,625 kg/h, about 234 tonnes over 22 hours. Bagasse = 34,091 kg/h.
  • Evaporation load = 130,909 × 0.75 = 98,182 kg/h. Each of the 5 bodies is 98,182 × 0.09 = 8,836 m².
  • Juice heaters = 130,909 × 0.02 = 2,618 m² each, 4 units. Vacuum filters = 113,636 × 0.004 = 454.5 m² each, 2 filters.
  • Clarifier = 130,909 ÷ 1,050 × 2.5 = 311.7 m³, shown as 400 m³.
  • Pans = 10,625 × 0.02 = 212.5 m³, shown as 250 m³ for each of 4. Crystallisers = 10,625 × 0.03 = 318.75 m³, shown as 400 m³ for each of 6.

Now run the mill for 24 hours instead of 22. The cane rate falls to 104,167 kg/h, the evaporation load to 90,000 kg/h (8,100 m² a body) and sugar to about 9,740 kg/h. The same mill looks smaller only because the hours are longer.

Reading the result

Imbibition is the lever to watch. Raising it from 28% to 35% increases the mixed juice and so the evaporation load and every body, because each litre added at the tandem has to be boiled off again. The tool shows the size of one unit and the quantity next to it, so a body of 8,836 m² is one of five, not the total. Pol sets the sugar rate and so the pans, crystallisers, centrifugals and bagging, but it does not change the mills or the evaporators. The basis text on each line states the rule behind its size.

What the tool assumes and leaves out

  • It prices nothing. You supply the rate for each line and no market prices are built in.
  • Recovery at 85%, bagasse at 30% of cane, juice water at 85% and syrup at 35% are fixed. Your own balance may differ.
  • The mill count (5), evaporator effects (5), pans (4), crystallisers (6) and centrifugals (6) are fixed, not calculated.
  • Not in the list: the boiler and turbo-alternator, the cane yard and weighbridge, the distillery, effluent treatment, the sugar godown and civil works. These are quoted separately.
  • Heat loads, steam economy and tube sizes are not worked out. For one evaporator body on its own, use the Heat exchanger area calculator.

Common mistakes

  • Entering cane per hour in the TCD field. The field is tonnes a day.
  • Reading a per-unit size as the total for the line.
  • Leaving imbibition at 28% when the mill runs at a different figure, then wondering why the evaporators look wrong.
  • Using 24 hours for a season plant that stops for cleaning every week.
  • Treating the rounded pan and clarifier sizes as a recommendation. They are stock sizes above the calculated volume.

Try your own figures in the Sugar mill calculator.

Keep reading