Steam pipe sizing: velocity and pressure drop
How to size a steam pipe from flow and pressure: convert kg/h to volume with steam tables, choose a velocity, check the pressure drop and pick a pipe size.
A steam main that is too small screams: high velocity, noise, erosion at bends and a pressure at the far end that is too low for the process. A main that is too big costs more to buy, more to insulate and loses more heat every hour it runs. Getting the size right is not hard once you remember one thing that makes steam different from water: steam pipe sizing is driven by volume, and the volume of a kilogram of steam changes a lot with pressure. This guide shows the two checks used in practice, velocity and pressure drop, with a complete worked example for a 2,000 kg/h line.
Why steam lines are sized by volume, not by mass
Boilers and process equipment are rated in kilograms of steam per hour, but a pipe only cares about how many cubic metres pass through it every second. One kilogram of saturated steam at 7 bar g occupies about 0.24 m³; the same kilogram at 1 bar g occupies about 0.89 m³, nearly four times as much. So the same mass flow needs a much bigger pipe at low pressure than at high pressure. That is why steam is usually distributed at a higher pressure and reduced close to the point of use.
Step 1: turn the steam flow into a volume flow
Multiply the mass flow by the specific volume of the steam at the line pressure:
Q = ṁ × vg
- Q = volume flow, m³/s
- ṁ = mass flow, kg/s (kg/h ÷ 3,600)
- vg = specific volume of saturated steam, m³/kg, from steam tables at the absolute pressure (gauge + about 1 bar)
Typical values for dry saturated steam (IAPWS-IF97):
- 1 bar g (2 bar a): 120.2 °C, vg = 0.886 m³/kg
- 3 bar g (4 bar a): 143.6 °C, vg = 0.462 m³/kg
- 5 bar g (6 bar a): 158.8 °C, vg = 0.316 m³/kg
- 7 bar g (8 bar a): 170.4 °C, vg = 0.240 m³/kg
- 10 bar g (11 bar a): 184.1 °C, vg = 0.177 m³/kg
For superheated steam, take the specific volume at the actual temperature from a superheated steam table; it is larger than the saturated value. Our steam and boiler duty calculator helps you get the mass flow in the first place from the heat load of your process.
Step 2: choose a velocity and work out the bore
With the volume flow known, the required inside diameter follows from the continuity equation:
d = √(4 × Q / (π × v))
Then pick the next standard pipe size and recalculate the real velocity with its actual inside diameter: v = Q / A, where A = π × d² / 4.
What velocity to design for
For saturated steam in mains and process lines, design velocities of about 25 to 40 m/s are commonly recommended. Saturated steam always carries some condensate droplets, and above that range they erode bends, valves and fittings and make the line noisy. Use the lower end for long mains, lines with many fittings, or wet steam; use the upper end for short, well-drained runs. Superheated steam is a dry gas and is often run faster, but check your company or supplier guidance for the exact figure.
Step 3: check the pressure drop
A pipe can have a sensible velocity and still lose too much pressure on a long run. The friction loss is found with the Darcy–Weisbach equation:
Δp = f × (L / d) × ρ × v² / 2
- f = Darcy friction factor (from the Moody chart or the Swamee–Jain formula; about 0.017–0.019 for commercial steel steam mains)
- L = equivalent length, m: the straight pipe plus an allowance for bends, tees and valves
- ρ = steam density = 1 / vg, kg/m³
How much pressure drop is acceptable?
A common rule of thumb is to keep the total drop along a main below 10 % of the supply pressure or 1 bar, whichever is less, and to check the pressure drop on any line longer than about 50 m regardless of its velocity. What really matters is the pressure the equipment at the end needs: if a heat exchanger was sized for 6.5 bar g, the main must deliver at least that at full load. The same friction method used for liquids in our pipe size and pressure drop calculator works for steam, as long as you use the steam density and viscosity.
Worked example: 2,000 kg/h of saturated steam at 7 bar g
A boiler supplies 2,000 kg/h of dry saturated steam at 7 bar g to a process 120 m away. With bends, valves and tees the equivalent length is taken as 150 m. The process needs at least 6.3 bar g, so the allowed drop is 0.7 bar (10 % of 7 bar, which is less than 1 bar). Pipe: carbon steel Schedule 40, roughness 0.045 mm.
Step 1: volume flow
- ṁ = 2,000 / 3,600 = 0.556 kg/s
- vg at 8 bar a = 0.2403 m³/kg, so ρ = 4.16 kg/m³
- Q = 0.556 × 0.2403 = 0.1335 m³/s
Step 2: bore for 25–40 m/s
- At 25 m/s: d = √(4 × 0.1335 / (π × 25)) = 0.0825 m = 82.5 mm
- At 40 m/s: d = 65.2 mm
The candidates are DN65 (inside diameter 62.7 mm) and DN80 (77.9 mm):
- DN65: A = 0.003086 m², v = 0.1335 / 0.003086 = 43.3 m/s, too fast
- DN80: A = 0.004769 m², v = 0.1335 / 0.004769 = 28.0 m/s, inside the range
Step 3: pressure drop in DN80
- Viscosity of steam at 170 °C ≈ 1.47 × 10⁻⁵ Pa·s, so Re = 4.16 × 28.0 × 0.0779 / 1.47 × 10⁻⁵ ≈ 619,000 (fully turbulent)
- Swamee–Jain with ε/d = 0.045 / 77.9 gives f ≈ 0.0181
- Dynamic pressure ρv²/2 = 4.16 × 28.0² / 2 = 1,631 Pa
- Per 100 m: Δp = 0.0181 × (100 / 0.0779) × 1,631 = 37,900 Pa = 0.38 bar
- For 150 m: 0.38 × 1.5 = 0.57 bar, below the 0.7 bar allowed
DN80 Schedule 40 passes both checks and is the answer. Strictly, the density falls a little as the pressure drops along the line, so the real loss is slightly higher than this one-step estimate; for drops under about 10 % of the pressure, the simple calculation is close enough.
What if the main were twice as long?
Keep the same flow but make the equivalent length 300 m. DN80 would now lose 0.38 × 3 = 1.14 bar, too much for a process that needs 6.3 bar g. Going up one size to DN100 (inside diameter 102.3 mm) drops the velocity to 16.3 m/s and the loss to 0.094 bar per 100 m, or 0.28 bar over 300 m. On long mains it is the pressure drop, not the velocity, that sets the size.
Imperial units cross-check
2,000 kg/h is 4,409 lb/h and 0.2403 m³/kg is 3.85 ft³/lb, so Q = 4,409 × 3.85 / 3,600 = 4.72 ft³/s. A 3-inch Schedule 40 pipe has an inside diameter of 3.068 in, an area of 0.0513 ft², giving v = 4.72 / 0.0513 = 92 ft/s (about 5,500 ft/min), which is the same 28.0 m/s. If you mix gauge and absolute pressure or bar and psi, the specific volume is the number that goes wrong; our engineering unit converter is a quick way to check each conversion.
Don't forget the warm-up load and the condensate
Sizing is done at the full running flow, but a cold main also condenses steam while it heats up. The warm-up condensate is roughly the mass of steel × its specific heat (about 0.49 kJ/kg·K) × the temperature rise, divided by the latent heat. For 100 m of DN80 Schedule 40 (11.29 kg/m) heated from 20 °C to 170.4 °C: 1,129 × 0.49 × 150.4 / 2,047 ≈ 41 kg of condensate. Warmed up over 20 minutes, that is about 120 kg/h on top of the process demand, and the traps and drain points must handle it. Once warm, the line still condenses steam at a rate set by its heat loss, which is why good insulation matters; size it with our insulation thickness and heat loss calculator.
Practical points that go with a correctly sized main:
- Slope the main down in the direction of flow (often about 1 in 100 to 1 in 250) and fit drain pockets with steam traps at low points and roughly every 30–50 m.
- Take branch connections off the top of the main, so they draw dry steam.
- Size the main for the future load if an extension is planned; a bigger pipe later costs far more than a bigger pipe now.
- Check the pipe wall and flange rating for the design pressure and temperature, not just the bore.
Common mistakes
- Sizing from mass flow alone. A table of "kg/h per pipe size" is only valid at the pressure it was made for.
- Using gauge pressure in the steam tables. Steam tables are in absolute pressure; add about 1 bar to the gauge reading.
- Ignoring fittings. Bends, tees and valves can add 20–50 % to the straight length on a typical plant main.
- Copying the boiler outlet size. The boiler's crown valve is sized for the boiler, not for your distribution length or the pressure your process needs.
- Forgetting low-pressure lines. After a pressure-reducing valve the specific volume rises sharply, so the downstream pipe is usually larger than the upstream one.
Summary
- Convert the mass flow to volume flow: Q = ṁ × vg, with vg at the absolute line pressure.
- Choose a velocity of about 25–40 m/s for saturated steam and find the bore: d = √(4Q / πv).
- Check the pressure drop with Darcy–Weisbach over the equivalent length; keep it within the pressure your equipment needs (often 10 % of supply or 1 bar, whichever is less).
- On long runs the pressure drop decides; on short runs the velocity decides.
- Allow for warm-up condensate, drainage and insulation.
This guide is for preliminary sizing. Final steam system design should follow the codes and supplier data that apply to your plant and be checked by a qualified engineer.