How a centrifugal pump works and what its curve tells you
A plain-language look inside a centrifugal pump, why head is quoted in metres, how to read a pump curve, and a worked power example for water and a heavier liquid.
The centrifugal pump is the most common pump in factories, farms and water systems. It has few moving parts, runs smoothly and handles a wide range of liquids. Understanding what happens inside it, and how to read its curve, helps you ask better questions when you choose one.
What happens inside the casing
Liquid enters at the centre of a spinning impeller, called the eye. The curved vanes throw it outward at high speed. The casing around the impeller, usually a spiral shape called a volute, slows the liquid down, and that lost speed turns into pressure. The liquid leaves through the discharge branch, and fresh liquid is pulled in behind it.
A standard centrifugal pump cannot move air well, so the casing and suction line must be full of liquid before it starts. This is called priming. Self-priming designs exist, but check this point whenever the pump sits above the liquid level.
Why head is quoted in metres
Pump makers describe the work a pump does as head, in metres of liquid. For a given pump at a given speed, the head is almost the same whether it handles water or oil. The pressure it produces is not the same, because pressure equals density × gravity × head. At 30 m of head:
- Water (1000 kg/m³): about 2.94 bar.
- Vegetable oil (about 910 kg/m³): about 2.68 bar.
- 50% caustic (about 1520 kg/m³): about 4.47 bar.
The heavier the liquid, the more power the same pump needs. Always tell the supplier the density and the viscosity, because thick liquids also lower efficiency.
Reading the pump curve
A pump curve plots head against flow at a fixed speed. Four things to look for:
- Head falls as flow rises. The pump gives its highest head at zero flow and less as the flow grows.
- The system curve. Your pipework needs a certain head at each flow: static lift plus friction, which grows with the square of velocity. The pump runs where the two curves cross.
- Best efficiency point (BEP). Efficiency peaks at one flow. Running far to the left or right of it wastes power and increases wear and vibration.
- NPSH. The net positive suction head available at the pump inlet must exceed the figure the maker requires, otherwise the liquid can vaporise inside the pump, a fault called cavitation.
Closing a discharge valve moves the operating point to the left on the curve. It works, but the pump then spends part of its power as heat.
A worked power example
Take a flow of 50 m³/h against a total head of 30 m, pumping water, with 70% pump efficiency and 92% motor efficiency.
- Hydraulic power = 1000 × 9.80665 × 50 × 30 ÷ 3,600,000 = 4.09 kW.
- Shaft power = 4.09 ÷ 0.70 = 5.84 kW.
- Motor input = 5.84 ÷ 0.92 = 6.35 kW.
- With a 15% margin: 6.35 × 1.15 = 7.30 kW, so the next standard motor is 7.5 kW.
Pump the 50% caustic instead and the same figures become 6.21 kW hydraulic, 9.64 kW motor input, 11.09 kW with margin, so a 15 kW motor is needed. The pump is the same; only the liquid changed.
Practical takeaways
- Give the supplier flow, total head, liquid, density, viscosity and temperature, not just a pump size.
- Choose a pump whose best efficiency point is close to your normal duty, not the maximum.
- Check that NPSH available is comfortably above NPSH required.
- Size the motor for the heaviest liquid the pump will ever handle.
To run your own numbers, use the pump head and power calculator. Confirm the final selection against the manufacturer's curves and datasheet.