How many MS or SS sheets does a tank really need?
Why dividing surface area by sheet area is not enough, how the plate calculator counts sheets as rolled rings, and a worked 10 × 15 ft mild steel tank.
Dividing a tank's surface area by the area of one sheet gives a neat number, but it is not how a shell is built. Plate is rolled into rings, every ring needs whole sheets around the circumference, and the top ring is often trimmed. The MS and SS plate calculator counts sheets the way a fabricator builds the shell, and gives plate area and weight next to the count.
How the calculation works
You enter the diameter and height, whether the height is the straight shell or the overall height including the ends, the top and bottom (open, flat, ellipsoidal 2:1, torispherical, hemispherical or conical), the material, thickness, sheet size and a wastage percentage. The tool then works through these steps:
- Circumference = π × D, and shell area = circumference × shell height.
- Rings (shell courses) = shell height ÷ sheet width, rounded up.
- Sheets per ring = circumference ÷ sheet length, rounded up.
- Shell sheets = rings × sheets per ring.
- Top and bottom sheets = (top area + bottom area) × (1 + wastage) ÷ sheet area, rounded up. A flat end is π × D² ÷ 4.
- Net weight = total area × thickness × density. Gross weight = sheets bought × sheet area × thickness × density.
Densities used: mild steel 7,850 kg/m³, stainless 304 at 7,930, stainless 316 at 8,000, stainless 409 at 7,800 and aluminium at 2,700.
Worked example (the values the tool opens with): a tank 10 ft in diameter with a 15 ft shell, flat top and flat bottom, mild steel 5 mm thick, 8 × 4 ft sheets (2438 × 1219 mm), 10% wastage.
- D = 3.048 m, shell height = 4.572 m, circumference = π × 3.048 = 9.576 m.
- Shell area = 9.576 × 4.572 = 43.78 m². Each flat end = π × 3.048² ÷ 4 = 7.30 m². Total = 58.37 m².
- Rings = 4.572 ÷ 1.2192 = 3.75, rounded up to 4. Sheets per ring = 9.576 ÷ 2.4384 = 3.93, rounded up to 4. Shell = 16 sheets.
- Top and bottom = 14.59 × 1.10 ÷ 2.973 = 5.40, rounded up to 6 sheets.
- Sheets to order = 16 + 6 = 22. One sheet weighs 2.973 × 0.005 × 7,850 = 116.7 kg, so the gross weight is 22 × 116.7 = 2,567 kg. The net weight of steel in the finished tank is 58.37 × 0.005 × 7,850 = 2,291 kg.
Four 4 ft rings stack to 16 ft, so 1 ft is trimmed off the top ring. That is why the tool also measures every stock size against the same tank. Here 8 × 5 ft sheets give three rings of exactly 5 ft:
Sheet | Rings | Per ring | Sheets | Waste | Last ring |
|---|---|---|---|---|---|
8 × 5 ft | 3 | 4 | 17 | 8.2% | exact |
8 × 4 ft | 4 | 4 | 22 | 12.0% | 1 ft off |
Waste here is the area bought over the area needed. With 8 × 5 ft sheets you buy 17 sheets (12 for the shell, 5 for the ends) and about 2,480 kg instead of 2,567 kg, with one ring weld fewer.
The ring plan goes one step further. It searches the sizes you stock, mixing at most two widths, and picks the stack with the fewest rings, then the least trimmed off the top, then the least plate bought. Every ring joint is a circumferential weld to set up, run and test, which costs more than the steel a narrower ring would save. Untick any size your yard does not carry and the plan and the comparison use only what is ticked.
What the tool assumes and leaves out
- Only the shell is built from rings. The ends are counted from flat plate by area plus wastage. The wastage percentage applies to the ends and to the theoretical area count, not to the ring layout, where offcuts already show up as whole sheets.
- No nozzles, manholes, stiffening rings, wind girders, supports, lap-joint overlap or weld preparation. Add those from your drawings.
- Dished ends are approximations. An ellipsoidal 2:1 end is taken as 1.084 times the flat circle and a torispherical end as 1.09 times; a hemispherical end is π × D² ÷ 2.
- The diameter is used as you type it. The tool does not adjust between inside, mean and outside diameter, so on thick plate decide which one you mean.
- No price is assumed. If you enter your own rate per kg, the tool multiplies it by the gross weight. That figure is plate only: no cutting, rolling, welding, consumables, transport or taxes. Steel rates change weekly and differ by city and mill, so use your own current quote.
- Thickness is not checked against any design code. The result is an estimating aid; confirm it against your drawings and the applicable code.
Common mistakes
- Ordering on the area count. Total area ÷ sheet area assumes perfect nesting and no seams. In this example the two counts happen to agree at 22, but on many tanks they do not. Order against the layout count.
- Entering the overall height as the shell height. If your figure includes dished ends, choose "Overall, incl. ends" so the head depths come off before the rings are counted.
- Using the gauge formula found online. The tool's SWG list follows the BS 3737 table: 18 SWG is 1.22 mm, 16 SWG is 1.63 mm and 14 SWG is 2.03 mm. The 0.127 × (32 − gauge) formula gives 1.778 mm for 18 SWG and overstates every gauge.
- Using mild steel density for stainless. 304 is 7,930 kg/m³ and 316 is 8,000 kg/m³; on a large tank the difference shows in the weight.
- Costing on net weight. Gross weight is what you buy, offcuts included. Net weight is the figure for foundation and lifting loads.
If you do not have the dimensions yet, size the tank first with the tank and vessel calculator, then count the sheets with the MS and SS plate calculator.